CLICK HERE FOR BLOGGER TEMPLATES AND MYSPACE LAYOUTS »

Thursday, December 17, 2009

Assignment 1: constructing a control


Almost any experiment you construct will require a control. Sometimes a positive control is needed sometmes a negative one is needed. your descision in selecting our control would depend on how you want to analyze your results.

A positive control would be an experiment you know would give you a positive reading. for example if you want to test if the leaves have starch you would have to have a test tube(TT) with starch already inside and tested with iodine. Any experiment with the same results as your control would mean that your experimental tube underwent the same reaction as the control

A negative control would be an experiment in which you know would give you a negative reading. This is what we call a baseline reading . for example, a negative control for assignment 1 would be a TT with just dH2O inside. The whole point of a negative control would be to allow you to get a net reading (ie a reading due purely to your experiment)

example:
if you place a yeast-glucose suspension in a syringe and immerse it in a waterbath at 30 C and obtain 25 bubbles per min.
Then place a negative control containing boiled yeast and glucose in the same waterbath and count no. of bubbles. (maybe 2 bubbles per minute)

net production of bubbles would be 23 bubbles per minute. You can then speculate that te other 2 bubles are due to some error (depending on the Q you may have to identify source of error)

In assignment 1 you have to decide what methodology to use with an appropriate control.

For example if I want to examine amount of starch produced by weight, I may need some leaves in a situation in which starch cannot be produced.(maybe place leaf disks in the dark or in dH2O )


Next: Analysing your results

Thursday, December 3, 2009

Assignment 1





Designing the experiment: selection of variables










In order to design an experiment several things must be taken into consideration.



Variables:

dependant and indipendant?

continuous or discreet?


Continuous variables are variables in which a wide range of values are expected or can be obtained. for example :age, time, height, weight, % of polymerization and light wavelengths. Usually continous variables are quantitative.


Discreet (discontinuous) variables are variables in which take a qualitative property. For example: colour, sex and species are discreet. It is possible to convert discreet variables into continous variables. For example instead of evaluating based on colour, it can be converted to 'reflected light wavelength"

Examples of variables seen in assignment 1 are:
temperature
leaf disc size
light intensity
level of destarched leaves
plant species
sugar type
sugar quantity

Bear in mind to include variables that have a possibility in affecting the experiment (either as a source of error or as a contributor to results)

things like leaf thickness, no. of stomata per disc are also variables but since they cannot be controlled are ignored. They can be used however to explain possible discrepancies in your results.
In an ideal experiment only one indipendant variable is mantained and its effect on a dependant variable is monitored. All other variables are mantained or kept constant.

If for exampler we want to examine the effect of sugar concentration then the following things must be mentioned.

  1. Stock sugar solution was diluted to the required concentrations. for example to create a 5g/L solution from a 10 g/L solution, take 100ml stock and add equal volume of dH2O.
  2. State all your required sugar concentration. Make sure you select a minimum of 5 ranges if the question does not specify no. and make sure they are reasonable values. for example do not say you are going to select a 12g/L solution when your stock is only 10g/L
  3. Mention which variables you will keep constant. for example :
  • all leaf discs were cut with a cork borer with a 1cm diameter
  • apparatus was set up in a regulated water bath with an electronic thermocoupler
  • apparatus was set up under a light source with constant light intensity (avoid saying under the sun as sunlight intensity can shift)
  • mention no. of leaf discs per experiment eg. 30 or 100 (select values which are reasonable for the experiment) if large samples are readily available then use large samples
  • time of experiment. how long does the experiment need to run. for something like this results could change very slowly over time so state something like 2 to 4 hrs.
note some methods automatically become precautions, especially if you state that the same step is conducted across the experiment (eg. mantain light intensity for all experiments, mantain temperature for all experiments.
next : designing a control

Assignment 1
Designing a hypothesis
.

A hypothesis for any experiment has to be designed in accordance to the objective you are trying to achieve. In the case of this experiment you want to find out the effects of certain parameters on the ability of plants to produce starch.

Things to consider:
Should your hypothesis be very strict?
(eg. increasing glucose concentration would result in increased starch storage )the disadvantage to a strict hypothesis is that the possibility of your actual experiment disproving your hypothesis to be very high.

A generic hypothesis would be : Increasing glucose concentrations will have a direct effect on starch storage capacity.

Can your experiment be designed to prove or disprove your hypothesis?
Depending on the apparatus given you might want to consider revising your hypothesis.(eg. the effect of different carbon numbers in carbon source will affect the starch storage rate)if there is no apparatus or indication in measuring the variables, a hypotesis should not be designed in that way .
Similarly you want to make sure that the experiment you design will minimize errors or at least allow them to be controlled.

How many hypothesis per experiment?
Ideally one experiment should be constructed to prove or disprove only one hypothesis. So one experiment should be designed for every hypothesis. Each hypothesis should be written as a separate sentence. Bear in mind it is still possible to have a multiple hypotheses proven/ disproven by a single experiment. It really depends on the overall design of the experiment.

next....Designing an experiment

Monday, August 3, 2009

bio correction stuff..

i know i am supposed to upload this earlier.. i hope this is not too late.. thanks for waiting guys!! lable the stuff yourself.. pandai pandai lor.. after today, i mean^^ good luck with tomorrow everyone~




sir stresses that the top half featuring the Dicot is more important..

the trachea drawing for this one has mistakes according to sir.. cos he says that one layer of sub-mucosa is missing, and also the cartilage is not supposed to be shaded..


thanks to Sheryn for letting us take pix.. did we miss any other pix?? we only managed to grab this much!! thanks to Sangeetha for mailing me the pix! nite guys~~

Tuesday, July 21, 2009

welcome^^

we got a new classmate today!! welcome Yoonyoon~ (chelle really went and asked her if we can call her that.. swt... but i agreed that it sounds cuter on her~~ lol)




we spent some time updating her on our class^^ stuff that circulates pretty well among us student that is.. hahaha.. no surprises which teacher gets the best coverage here..

WhAt hApPeNeD iN PM1 ? ! ? !

P M 1 W i T h M d m C h i n . . .


















A p R i L f O o L . . .




W i T h M r . A g a s . . .



























W i t H M s . G l a d y s . . .






















P M 1 d A n C i N g L e S s O n . . .


R a B i N a s M r. A g a s . . .



A f T e R t H e M o V i e . . .